Eltron LP2122 Manual do Utilizador

User’s Manual No. 980008-001Rev. B©1995 Eltron International Inc.LP/LP+ SeriesUser’s ManualModels:LP2022, LP2042LP2122, LP2142

InstallationThe following sections will step you through theinstallation of the printer and Create-A-LabelTools software.Step ➊Attach PowerSupplyPlace

Step ➋Insert MemoryCartridge(LP+ Only)The memory /real-time clock cartridge pro-vides permanent storage for downloadedforms and time/date information.

Step ➌Attach InterfaceCableParallel InterfaceAttach a suitable parallel printer cable from thecomputer to the Centronics interface connectoron the rea

Step ➍Install Software(LP+ Only)Start your computer. After DOS has loaded,insert the Creat-A-Label Tools diskette intoyour floppy disk drive. From the

Getting Started8980008-001 Rev. B

2OperationThis section provides information on the op-eration of the LP and LP+ printers.Controls &IndicatorsThe printer’s power switch is located

PowerSwitchFigure 2-1Controls & IndicatorsPowerIndicatorFeedControlTensionReleasePush BackTo ReleaseLabel TakenSensorOperation10980008-001 Rev. B

The FEED ControlThe FEED control can be used in two ways,tapping or holding. When power is first ap-plied to the printer, tapping the FEED controlwill

Loading Labelsor TagsYour printer can print on adhesive backedlabels or non-adhesive tags. Loading eithertype of material is easy, however the feeddir

Step ➊Open the top cover and remove the spindlefrom the printer. Place the spindle inside theroll of labels or tags.Cutting the corners off the end of

Step ➋Adjust the guide tabs to their widest position bypushing one or both towards the sides of theprinter.Step ➌Insert the end of the roll into the f

Step ➍While continuing to gently push the labels intothe feed slot, press the FEED control to ad-vance labels until the end is visible at the frontof

Step ➏Rewind the excess paper onto the roll whileplacing the spindle into the holder slots.Step ➐Tap the FEED control 3 times or until thePOWER indica

Threading TheLabel DispenserIf your printer is equipped with the optionallabel dispenser and you would like the printerto automatically peel adhesive

Step ➍Press the FEED control to feed the leaderthrough the dispenser.Step ➎Push the Label Release towards the rear of theprinter and pull the excess l

AutoSenseGap SensorAdjustmentYour printer is equipped with a sensor capableof detecting the gap between labels while theyare being printed. This featu

Cleaning ThePrint HeadAs you use your printer, the print head maybecome dirty resulting in poor print quality.Whenever new labels are loaded into thep

Replacing thePrinter MemoryBackup Battery(LP+ Only)The Memory Cartridge provides storage of op-erating parameters, forms, graphics and softfonts. A ba

BatteryReplacementStep ➌Remove the Memory Cartridge’s top coverscrew with a #1 Phillips screwdriver. Slide thecasing top cover off.Step ➍Lift the bat

Do Not dispose of the old battery in fire. Thebattery may explode causing damage or injury.Dispose of the battery according to the manu-facturer’s ins

FOREWORDThis manual provides installation and operation information for LP & LP+ Series printersmanufactured by Eltron International Incorporated,

Operation24980008-001 Rev. B

Appendix ATroubleshootingThis section addresses the most common issuesuser’s may face with operation and configura-tion of your printer.The first trou

Common Printing ProblemsToruble Shooting GuideProblem Solution or ReasonPOWER indicator does not lightGreen when power switch isturned to “1" (ON

Serial InterfaceCable WiringThe figure below displays the cable wiring re-quired to use the printer’s serial interface.N/CRxDTxDDTRGNDDSRRTSRICTSPrint

Removing StuckLabelsUnder certain conditions, labels can becomestuck inside the printer on the print head or themechanism. This usually occurs when th

Step ➊Remove Top CoverMove the power switch to the OFF (0) positionand disconnect the power and interface cables.Place the printer upside down and rem

Step ➋Remove The PrintHeadThe most common location of stuck labels is atthe print head. Check this area first beforechecking the remainder of the prin

While lifting the lower head bracket, removethe tension release rod. Without disconnectingand cables, lift and rotate the print head so thatthe surfac

Step ➌Install The PrintHeadTo install the print head, first position it backover the platen. Lift the front slightly and insertthe tension release rod

Step ➍RemoveMechanismLabels can become stuck to several parts in sidethe print mechanism. To clear labels stuck in-side the mechanism, it must be remo

WARRANTY INFORMATIONWe Need To Hear From You!To establish your warranty period and provide access to Technical Support,Send Us Your Product Registrati

Step ➎Remove SensorAssemblyLocate the push tabs on the rear of the mecha-nism. While pushing in on both tabs, pull thelower sensor assembly away from

Step ➏Install PrintMechanismReplace the lower sensor assembly by slidingback into the mechanism until it locks in place.Reconnect the four connectors

Troubleshooting36980008-001 Rev. B

Appendix BSupplies andAccessoriesSupplies and Accessories can be ordered fromELTRON by calling: 1(800) 344-4003.Eltron gladly accepts Mastercard and V

Accessories38980008-001 Rev. B

Appendix CWindows PrinterDriverTo install the Windows printer driver, use thefollowing steps. Start your computer and thenstart Windows. Insert the Wi

Using TheWindows DriverThe Windows printer driver provides controlof several printer features when printing fromCreate-A-Label Professional for Window

Paper Quality,Print SpeedThe print speed can be adjusted to compensatefor manufacturing differences in label stock.Selecting a slower print speed can

41 More la nd Rd.Simi Va lle y, C A 93065-1692(805)579-1800

Table Of ContentsGetting StartedIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . 1Unpacking the Printer . . . . . . .

vi980008-002 Rev. B

1Getting StartedThis section provides information on the instal-lation of the printer and software.IntroductionThe LP Series and LP+ Series printers a

Unpacking thePrinterThe printer is shipped in a carton and protec-tive bag. Keep all packing material in case youneed to move or re-ship the printer.

Parts Check ListYour printer kit should contain the items listedbelow.• The LP or LP+printer.• The printer Power Supply.• Create-A-Label Tools softwar